Search found 5 matches
Search found 5 matches
· Page 1 of 1
- by kolo
- Sun Apr 09, 2017 10:04 pm
- Forum: Welding Forum General Shop Talk
- Topic: welding bushings for shafts
- Replies: 6
- Views: 1381
Re: welding bushings for shafts
Anyway I wanted to do this in my first attempt with O45 dual shield, got a spool of Hobart wire, but when I opened the cabinet storage area I quickly discovered I do not have O45 FC drive rollers, could of swore I did.LOL So anyway it's hard wire mig 25.5 and 470 ipm, looks like this. thumb 3.jpg ju...
- by kolo
- Sun Apr 09, 2017 9:40 pm
- Forum: Welding Forum General Shop Talk
- Topic: welding bushings for shafts
- Replies: 6
- Views: 1381
Re: welding bushings for shafts
on that small shaft, it started to bind up badly, but by skipping and welding back to back I got it to slide silky smooth just like before welding, but I think I got lucky, I was not so lucky with the large shaft, it is only tacked now but don't want to go further until I get some advice, or real &q...
- by kolo
- Sun Apr 09, 2017 9:38 pm
- Forum: Welding Forum General Shop Talk
- Topic: welding bushings for shafts
- Replies: 6
- Views: 1381
Re: welding bushings for shafts
OK think I might have picture thing worked out but not resized , here goes thumb 1.jpg thumb 2.jpg now I know I can leave the shaft in, and at first shaft slides back and fourth silky smooth, but even welding with shaft in, bushings turn and distort making the shaft impossible to move by hand and ev...
- by kolo
- Sun Apr 09, 2017 9:06 pm
- Forum: Welding Forum General Shop Talk
- Topic: welding bushings for shafts
- Replies: 6
- Views: 1381
welding bushings for shafts
welding a kit together to construct a thumb for a mini excavator . among the components are brackets that are lazer cut that will retain the hydralic cylinder ram. And also the main pin to bolt the thumb and excavator bucket on. the bores are a little oversized and the bushings slip inside of them t...
- by kolo
- Thu Apr 07, 2016 10:34 pm
- Forum: Video Discussion
- Topic: pipe welding with JD Brewer
- Replies: 3
- Views: 2578
Re: pipe welding with JD Brewer
Jody, JD I'm assuming you switched power input over to 230 when you started the dual shield work on the pipe joint. I picked up 1 of these Lincoln 210 MP's , when I demoed it at the dealer I welded 1/8 stick 7018 on 115 and was pretty impressed. However when I got it home I tried that and kept blowi...
Search found 5 matches
· Page 1 of 1
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities