Search found 6 matches
Search found 6 matches
· Page 1 of 1
- by jem44357
- Wed Mar 17, 2010 7:18 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
Re: New guy with a questions.
OK, so this is what I did for the best bang for my buck. I purchased these... Hobart Handler 140 Welder Process Type: MIG, Flux Core Welding Amperage Range: 25-140 A Input Voltage: 115 VAC Weld Thickness: 24 ga. - 1/4 inch - Single Pass Duty Cycle: 20% @ 90 A, 19VDC Width: 10-3/4 in. Length: 19-1/2 ...
- by jem44357
- Thu Feb 18, 2010 5:00 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
Re: New guy with a questions.
OK, dead end on the electric start. Briggs does not make or stock the flywheel I need. I searched around and I cannot find one. My flywheel will not accept the ring gear they have. I am definitely going to purchase a new welder. Maybe one to replace the Lincoln. This means I would also need to purch...
- by jem44357
- Thu Feb 11, 2010 6:36 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
Re: New guy with a questions.
i find in automotive welding that some projects can just be too dirty for tig. fluxcore, is usefull, and the wire should be inter changable with mig wire in that sort of setup, so you get the best of both worlds. When your metal is too rusty or thin for a fluxcore(FC needs more heat) I use the mig....
- by jem44357
- Thu Feb 11, 2010 6:35 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
Re: New guy with a questions.
Why not look at an electric starter? Sorry it's taken so long to respond. I've been busy. I have searched through Lincoln/B&S stuff but can't find a direct straight answer for the model and or serial numbers I have. I need to take my numbers to a service center for B&S and have them help me...
- by jem44357
- Wed Jan 27, 2010 1:16 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
Re: New guy with a questions.
Thanks for the input. As far as the hard to start it is relative to me being short and the stroke of the pull start being long. This is augmented by the fact that it sits on a raised shelf under my welding table ~6" up. When I pull it I am lucky to get 1 rev it seems to like 2. If I put it on t...
- by jem44357
- Tue Jan 26, 2010 5:55 am
- Forum: Welding Forum General Shop Talk
- Topic: New guy with a questions.
- Replies: 10
- Views: 2577
New guy with a questions.
Hi all, I have a Lincoln stick welder/generator along with a set of torches. My welding skills and knowledge are limited and I do not weld much. The Lincoln is a hassle because it is an 8hp Briggs which is hard for me to pull start and it is loud, this is the reason for lack of skills because of no ...
Search found 6 matches
· Page 1 of 1
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities