Search found 4246 matches
- by Oscar
- Tue Jul 20, 2021 9:17 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: CFH... where do you set it?
- Replies: 18
- Views: 7118
Re: CFH... where do you set it?
there have been a number of discussions here and elsewhere about how flow meters are calibrated, and the output pressure is a factor. Since the gauge/scale on the flow meter is calibrated for the output pressure of the regulator I would think you'd get a different number if the peashooter wasn't ca...
- by Oscar
- Tue Jul 20, 2021 9:07 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: CFH... where do you set it?
- Replies: 18
- Views: 7118
Re: CFH... where do you set it?
I use the pea shooter (aka floating ball) type flowmeters at the tank to begin with. So where do I set it? Just there at the tank. If I get porosity, I adjust the flow as needed, regardless of what the numbers on the flowmeter say. IOW, if it's too low, it's too low; and if it's too high, it's too ...
- by Oscar
- Mon Jul 19, 2021 10:41 pm
- Forum: Welding Projects - Welding project Ideas - Welding project plans
- Topic: Support Frame/Beams for garage rack/shevles
- Replies: 6
- Views: 4310
Support Frame/Beams for garage rack/shevles
I have some cheapie walmart/big box store garage racks, and the particle board was sagging quite a bit with the weight... https://drive.google.com/uc?export=view&id=1gd3n4ExmDuSjajtPDQOXVAPnj5cZrmTi https://drive.google.com/uc?export=view&id=1ghsnjxq-wVjxL84Se6G5OjhBGcNyV5cj ...so I used Fus...
- by Oscar
- Mon Jul 19, 2021 8:34 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: CFH... where do you set it?
- Replies: 18
- Views: 7118
Re: CFH... where do you set it?
I use the pea shooter (aka floating ball) type flowmeters at the tank to begin with. So where do I set it? Just there at the tank. If I get porosity, I adjust the flow as needed, regardless of what the numbers on the flowmeter say. IOW, if it's too low, it's too low; and if it's too high, it's too h...
- by Oscar
- Sat Jul 17, 2021 12:04 am
- Forum: Suggestions, Feedback and Support
- Topic: Format question....
- Replies: 17
- Views: 18054
Re: Format question....
It's only on the home page. Once you go into a sub-forum, it's no longer there.
- by Oscar
- Thu Jul 15, 2021 8:04 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Stainless practice. Adding filler makes a mess.
- Replies: 6
- Views: 1582
Re: Stainless practice. Adding filler makes a mess.
15 CFH is fine if A) you were using a much shorter tungsten stickout from the cup, or B) you were welding an inside corner type of joint that naturally traps argon and keeps it lingering around longer. I would say either decrease the stickout to half of what you are presenting OR bump it up to 20-25...
- by Oscar
- Thu Jul 15, 2021 3:10 pm
- Forum: Suggestions, Feedback and Support
- Topic: Format question....
- Replies: 17
- Views: 18054
Re: Format question....
click the little icon on the right that has the double arrows (left & right). That toggles the sidebar. That's all I can offer. ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
- by Oscar
- Thu Jul 15, 2021 11:36 am
- Forum: Suggestions, Feedback and Support
- Topic: Format question....
- Replies: 17
- Views: 18054
Re: Format question....
Why is it bad on your laptop/desktop? Seems fine to me. Different, yes, but fine altogether.
- by Oscar
- Thu Jul 15, 2021 12:27 am
- Forum: Welding Forum General Shop Talk
- Topic: When/Where is the best deals on MP machine? And booth set-up
- Replies: 1
- Views: 1931
Re: When/Where is the best deals on MP machine? And booth set-up
Close to your budget, and even though it is out of stock at the moment, but this is a quality machine that I would recommend: HTP 210 MTS . I have the pulse-capable version of that one and unless you are doing more than medium-level fabrication type work or need to constantly weld 3/8"+ steel/a...
- by Oscar
- Wed Jul 14, 2021 6:44 pm
- Forum: Member Introductions
- Topic: Hello from New Mexico
- Replies: 1
- Views: 3704
Re: Hello from New Mexico
Welcome Charlie
- by Oscar
- Mon Jul 12, 2021 9:39 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: HTP MTS 220
- Replies: 3
- Views: 2506
- by Oscar
- Sat Jul 10, 2021 10:16 pm
- Forum: Metal Cutting
- Topic: Evolution Rage 2 carbide blade sharpened by WD Quinn Saw Co.
- Replies: 17
- Views: 8957
Re: Evolution Rage 2 carbide blade sharpened by WD Quinn Saw Co.
Sending in more blades to get fixed sharpened. https://drive.google.com/uc?export=view&id=1be0ltslKtdja7-KFshC2-bIzzUbyUhJi Accidentally dropped and chipped a couple teeth on the Tomax and the Evo multi-material blade that I already had sharpened (it is relegated only for chopping up oak firewoo...
- by Oscar
- Sat Jul 10, 2021 8:33 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Miller MDX 100/Tweco 150 for Pulse
- Replies: 4
- Views: 2392
Re: Miller MDX 100/Tweeco 150 for Pulse
I'm under the impression that the MDX gun that Miller supplies with the 255 was developed to work with pulse. Yes, basically any MIG gun will work with pulse, it's all about how much heat it can handle and if there are high-heat tips for that MIG gun. The MDX will be better than any mig gun that is...
- by Oscar
- Sat Jul 10, 2021 4:37 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Miller MDX 100/Tweco 150 for Pulse
- Replies: 4
- Views: 2392
Re: Miller MDX 100/Tweeco 150 for Pulse
At what proposed amperage levels do you plan to pulse weld?
- by Oscar
- Sat Jul 10, 2021 12:31 pm
- Forum: Metal Cutting
- Topic: Question about metal cutting blades on the chop sawQuestion about metal cutting blades on the chop saw
- Replies: 3
- Views: 3290
Re: Question about metal cutting blades on the chop sawQuestion about metal cutting blades on the chop saw
A billet what? Of steel? Of Aluminum? Of copper?
- by Oscar
- Thu Jul 08, 2021 7:37 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Non syngeric pulse mig settings
- Replies: 3
- Views: 2193
- by Oscar
- Thu Jul 08, 2021 5:42 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Non syngeric pulse mig settings
- Replies: 3
- Views: 2193
Re: Non syngeric pulse mig settings
While I don't have experience with manual pulse settings, I do have some "white papers" that I could share if you care to read through them.
- by Oscar
- Mon Jul 05, 2021 7:43 pm
- Forum: Mig and Flux Core - gas metal arc welding & flux cored arc welding
- Topic: Argon tank empty??
- Replies: 11
- Views: 7680
Re: Argon tank empty??
well how did he check to see that it is "almost full"?
- by Oscar
- Thu Jul 01, 2021 9:42 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Cracks in AL fusion every time
- Replies: 28
- Views: 3844
Re: Cracks in AL fusion every time
This is quickly becoming all about amps. Like cj737 said, with aluminum it is ALWAYS about amps when using a standard TIG approach with only Argon shielding gas (and assuming everything else is in order). You simply need a buttload of it at the beginning, especially with small parts, as they will r...
- by Oscar
- Thu Jul 01, 2021 1:25 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Cracks in AL fusion every time
- Replies: 28
- Views: 3844
Re: Cracks in AL fusion every time
1/4" aluminum with only 160A is way, way outside the box...like double the thickness you should plan for with that size machine. Pre-heat will obviously help, but I'd be looking to find a way to add helium to the setup as well. I've tried 1/4" aluminum with a 200A machine and it was possi...
- by Oscar
- Wed Jun 30, 2021 7:03 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Cracks in AL fusion every time
- Replies: 28
- Views: 3844
Re: Cracks in AL fusion every time
Yup pretty much. Aluminum does not take well to autogenous welds.
- by Oscar
- Mon Jun 28, 2021 6:46 pm
- Forum: Member Introductions
- Topic: Hello all
- Replies: 2
- Views: 3824
Re: Hello all
welcome
- by Oscar
- Sun Jun 27, 2021 11:19 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Review for TIG Button hand amptrol for HTP Invertig 221
- Replies: 88
- Views: 21418
Re: Review for TIG Button hand amptrol for HTP Invertig 221
Sorry to dig this up again but I figured this might be the best way to possibly get some of older posters on here to come back and give their thoughts. So I've been debating a button for a bit now but I'm curious, how have they held up long term for you guys? And what kind of shop do you use them i...
- by Oscar
- Thu Jun 24, 2021 10:31 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Is this the result of improper gas flow or unclean metal?
- Replies: 14
- Views: 1695
Re: Is this the result of improper gas flow or unclean metal
Sounds like your gunna have to bump the pedal or trigger after your bead to keep the gas flowing. Sent from my Pixel 3a using Tapatalk Exactly. If it is set for only 2 seconds you're going to be in for a world of exhaustion with so much tungsten cleaning. If you're dead set on using this machine, r...
- by Oscar
- Thu Jun 24, 2021 10:24 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Operation of Advanced Pulse
- Replies: 4
- Views: 783
Re: Operation of Advanced Pulse
Your question is about volts but your diagram is showing amps. There might be a slight phase difference because of the reactance of the arc but the waveforms will be the same shape. I am asking if the low current DCEN section is simply interrupted by a periodic but otherwise typical AC TIG current....
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities