im with ya on the torq i could care less if it only does 120 but i wana be there yesterday iv always loved torq id like to hear your input on the cams and upgrades that i mentioned in the last post visually its not undercut allot but enough that i lost like 30 on the flow bench im just thinking to m...

so howd i do on the explanation part of the deal to a "professional" :) well since you had to mention your an MMI man, maybe you could help me out a little oh, i could have the heads hot tanked for ya before i ship them if you want. iv got an 01 sportster (1200) and im so so close to order...

ill work on that for ya, do you know anything about car heads or motorcycle heads ? there is a steel ring (valve seat) that is where the valve rests when its in the closed position. when you port a set of heads you remove material just below, right up to the valve seat for smooth,fast flow but if yo...

i might not be close (mn)
but the guys in the brown trucks could be

hello, i purchsed a set of harley heads from a guy that said they were ported and all this good stuff and after i had recieved them i looked them over real good and whoever did the job undercut the head where the valve seat is, to anyone that knows anything about motors knows this creates big proble...

i agree with you kermdawg overkill it is, im thinking that they used 6ga because it was left over from when the builder installed the hot tub thats the only other thing in the house that has 6ga wire. i agree, every type of welding has its place, theres a reason why there is just more than 1 type of...

is a flowmeter any better than a regulator or vise versa
since i am looking to replace this one
thanks
will be for c25 or straight argon

there are no leaks anywhere other than from on top of the flow meter tube inside the black rubber thing where the brass pc and the screen is

thanks for the comments guys, 6 amp for the dryer is allot i thought too, but the dryer is also about 115 ft from the panel (thats how long the wire was). i thought the pre/post flow module for that welder would only control the mig part of the machine. not the tig. i guess i never checked into it f...

nomatter what i do i cant get the flow meter to go above about 22
iv never had a flow meter before only regulators.
i do hear a slight hissing/flow of air from the top of the flow meter any time the tank valve is open, is that normal
any help would be great, thanks

i know, i know, you have read a million of these but im just soo excited gotta share. today our clothes dryer took a crap and we had to buy a new one, so i explained to the wife how a gas dryer would be a better route than an electric one. so on the way home from getting the dryer i stopped by a pic...

im glad it works but dummy me didnt do one at a time to figure out what was really wrong and just fixed it all at once.
now ill never know.

now for the next task.

1. i am looking to weld some alum. what type of gas do i use ?
2. can you weld alum with a flux welder ? and how ?

well, i got it working. all it took was me to bring it in the house to the 3rd story and open the window and said if you decide not to work ill throw you out. tada it works. jw i put a new liner in,new tip,took the ground clamp/wire all arpart and wire wheeled it all shiney and put on a new nut and ...

thanks for all the help guys

still no change in the machine. how would i check how many amps the machine is putting out on each setting ? the only reason i ask is because a car battery can have 12 volts but no amps so it will not start a vehicle but work great to run your ice fishing lights for a while and i assume that the wel...

this might sound dumb but what does poor contact with the tip of the gun and the wire have to do with anything ?? i understand/know about the dirty part and that they do get worn out. the volt readings that i supplied in previous post are taken both from the wheel area and from the gun end there was...

i was thinking the same. except i wonder if it might be easier/smarter to just install the solid wire nozzle and solid wire along with the gas solenoid to my flux machine that way if it does work then i just use it and screw the other one, lol for the time being anyway. i was going to check the grou...

ill work on getting a picture for you. with my flux core on the lowest setting i can easily blow a hole in thick wall exhaust tube (which should be really close to 18 ga) with the gas version still no change from the last test other than it did stick to the metal a little bit more but still just kin...

i understand about being thick metal and penetration. but im not getting any. i could scrape the welds off the metal with a putty knife setting a 19.6 volts b 22.4 c 25.8 d 29.5 the readings i got were not all that much different than my flux core welder so i cant imagine that is the problem. the me...

ground connected directly to the piece at the furthest distance away 6" from wire only c02 straight to wall its clean steel, id say 1/8 material but material shouldnt matter with my problems if the metal was too thick it would still penetrate the metal just not all the way drive and wheel is fi...

hey guys, iv been searching and reading the sight for about a month on and off just reading what people had to say and was content with that. but today i purchased a lincoln weld pak 100 from a guy (it has the gas conversion done) and when i tried to weld the wire would feed and there would be a rea...