Search found 16 matches
Search found 16 matches
· Page 1 of 1
- by mopeep
- Sun May 14, 2017 2:49 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Aluminoob freshman at Collier University
- Replies: 13
- Views: 1555
Re: Aluminoob freshman at Collier University
Yes, I took a long break making these posts and when I went back on the aluminum I was modulating and controlling heat just like I have been for a couple years working on mild steel. I can't figure what setting I abused to get pedal to act like on-off switch. Is that even possible? good advice about...
- by mopeep
- Sun May 14, 2017 2:01 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Aluminoob freshman at Collier University
- Replies: 13
- Views: 1555
Re: Aluminoob freshman at Collier University
Yes I agree there is lots of brainpower available from all you guys to figure out most any issue and photos greatly increase communication. I appreciate the help tremendously. Here is my AHP control panel. Have since had pretty good luck with 1/8 inch aluminum using AC main amps at 135, start amps a...
- by mopeep
- Sun May 14, 2017 11:16 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Aluminoob freshman at Collier University
- Replies: 13
- Views: 1555
Re: Aluminoob freshman at Collier University
Its easier to figure this welding stuff out by trial and error than to upload a photo.
will keep figuring out photo and get back to you
will keep figuring out photo and get back to you
- by mopeep
- Sun May 14, 2017 8:22 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Aluminoob freshman at Collier University
- Replies: 13
- Views: 1555
Re: Aluminoob freshman at Collier University
no upslope
- by mopeep
- Sun May 14, 2017 7:32 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: Aluminoob freshman at Collier University
- Replies: 13
- Views: 1555
Aluminoob freshman at Collier University
I'm fairly new to tig and have been getting semi-passable mild steel results for my furniture and art projects, but am flummoxed by something on aluminum. My foot pedal controls amps nicely in DC setting when welding steel, but when I switch to AC with no pulse the pedal acts like an on/off switch. ...
- by mopeep
- Sun Mar 26, 2017 8:16 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: How Much Skin Protection for TIG UV?
- Replies: 26
- Views: 3720
Re: How Much Skin Protection for TIG UV?
For gosh sakes don't TIG while wearing a "polo" type shirt. A couple of years ago I ordered a new Alpha 200 and got all my gear together while waiting on shipment. Tig gloves, protective sleeves, had my Ar bottle full. I was ready to go when the big day came and the brown truck came by. I ...
- by mopeep
- Tue Oct 13, 2015 4:37 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: AC problem
- Replies: 13
- Views: 1855
Re: AC problem
Thanks Southpaw.
I'm just a beginner with TIG, but so far the AHP has exceeded my expectations. Jody's videos and advice from this forum has really helped my progress.
I'm just a beginner with TIG, but so far the AHP has exceeded my expectations. Jody's videos and advice from this forum has really helped my progress.
- by mopeep
- Sun Oct 11, 2015 5:17 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: AC problem
- Replies: 13
- Views: 1855
Re: AC problem
Yep, balance.
AHP is bass ackwards. re-set to 25% and immediately started laying down beads. Moved too slow at first and got hot cracking. set amps to 150, got on the pedal, and started motoring with no problem.
1/8 4043. 1/16 melted before I got close to the puddle.
Thank you everyone!
AHP is bass ackwards. re-set to 25% and immediately started laying down beads. Moved too slow at first and got hot cracking. set amps to 150, got on the pedal, and started motoring with no problem.
1/8 4043. 1/16 melted before I got close to the puddle.
Thank you everyone!
- by mopeep
- Sun Oct 11, 2015 2:41 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: AC problem
- Replies: 13
- Views: 1855
AC problem
Am a noob, but with some coaching, I have been doing some semi-decent mild steel tig. Tried to light up on aluminum for the first time ever this am and met with total disaster... don't even know what to think. tungsten melted immediately and crap flew all over the table Aluminum turned black and loo...
- by mopeep
- Sat Sep 26, 2015 3:26 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: New bottle now brown soot
- Replies: 2
- Views: 453
Re: New bottle now brown soot
BTW, I switched back to known good bottle of argon and everything welded perfectly. Again switched to new bottle and it was as if I was welding w/o gas.
Guess I will be going back to LWS next week.
Guess I will be going back to LWS next week.
- by mopeep
- Sat Sep 26, 2015 11:32 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: New bottle now brown soot
- Replies: 2
- Views: 453
New bottle now brown soot
I think I may know the answer to this one, but would like another opinion. Running a few beads on a mild steel project this am and argon bottle got close to empty. I switched over to a fresh bottle I picked up last week at LWS, purged the lines to the torch, changed nothing on settings or equipment,...
- by mopeep
- Fri Sep 11, 2015 4:44 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: tig t joint with different thickness steel
- Replies: 6
- Views: 739
Re: tig t joint with different thickness steel
Minnesota Dave and others,
Cranked the amps to 130 and worked the pedal. 'sneaked the puddle" over to the thin stuff, kept it motoring along, and things went great.
Thank you again.
Cranked the amps to 130 and worked the pedal. 'sneaked the puddle" over to the thin stuff, kept it motoring along, and things went great.
Thank you again.
- by mopeep
- Wed Sep 09, 2015 7:37 pm
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: tig t joint with different thickness steel
- Replies: 6
- Views: 739
Re: tig t joint with different thickness steel
Great advice, I will give it a go this weekend. Gotta pay the bills until then.
- by mopeep
- Wed Sep 09, 2015 8:30 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: tig t joint with different thickness steel
- Replies: 6
- Views: 739
Re: tig t joint with different thickness steel
Thank you, will try hotter technique and sneak the puddle .
M
M
- by mopeep
- Wed Sep 09, 2015 7:26 am
- Forum: Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- Topic: tig t joint with different thickness steel
- Replies: 6
- Views: 739
tig t joint with different thickness steel
Hi all, Newby here having trouble with tig t joint. Mild steel-16 gauge vertical welded to 1/8 inch base plate Parameters: Tig 70 amps DC, no pulse 15 cfh argon ck9f torch w/gas lens #9 cup 3/32 2% lanth sharpened to 3/16 cone 1/16 ER70 filler When I hold a real tight arc of about 1/8 inch directed ...
- by mopeep
- Wed Sep 09, 2015 7:05 am
- Forum: Member Introductions
- Topic: Hello
- Replies: 2
- Views: 348
Hello
Another (older) newby posting for the first time. I grew up oxyacetylene cutting and stick welding farm equip to keep it running, but moved on to other pursuits (such as actually making money). Just within the last few years I got the itch to start making steel yard art and wooden and steel furnitur...
Search found 16 matches
· Page 1 of 1
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities