I've been eyeing a planishing hammer at harbor freight but from what I see, one sorta needs to use both hands to control your piece of metal. As I can't use a foot pedal I'm looking at maybe rigging up a mouth operated valve. We have people here from many industries and I may be trying to reinvent the wheel or overlooking some other solution. Any ideas would be welcomed.
Thanks
Cheers.
Eldon
General welding questions that dont fit in TIG, MIG, Stick, or Certification etc.
We are not lawyers nor physicians, but welders do it in all positions!
Miller Dynasty 280DX
Lincoln 210 MP
Miller 625 X-Treme
Hobart Handler 150
Victor Oxygen-acetylene torch
Miller/Lincoln Big 40-SA200 hybrid
Miller Dynasty 280DX
Lincoln 210 MP
Miller 625 X-Treme
Hobart Handler 150
Victor Oxygen-acetylene torch
Miller/Lincoln Big 40-SA200 hybrid
A low pressure differential switch and a length of hose could trigger a relay and then your hammer, if electrically controlled.
If it's a pneumatic hammer, add a solenoid valve to the air line to actuate the hammer.
Here is a switch that is marketed toward sky-divers to trigger their cameras, but there are other options on ebay. I'm not sure what pressure range you'd be best off with.
http://www.rockskymarket.com/camera-swi ... witch.html
I found the medical marketed switches being called "sip/puff switches" but they are priced as medical devices, in the $300 range.
If it's a pneumatic hammer, add a solenoid valve to the air line to actuate the hammer.
Here is a switch that is marketed toward sky-divers to trigger their cameras, but there are other options on ebay. I'm not sure what pressure range you'd be best off with.
http://www.rockskymarket.com/camera-swi ... witch.html
I found the medical marketed switches being called "sip/puff switches" but they are priced as medical devices, in the $300 range.
-Josh
Greasy fingered tinkerer.
Greasy fingered tinkerer.
Thanks. I knew someone on here would have a good idea. That looks like just the ticket. That switch and a solenoid valve and I'll be set. I think I'll rig something similar for the pedal on my electronic piano
Cheers
Eldon
Cheers
Eldon
We are not lawyers nor physicians, but welders do it in all positions!
Miller Dynasty 280DX
Lincoln 210 MP
Miller 625 X-Treme
Hobart Handler 150
Victor Oxygen-acetylene torch
Miller/Lincoln Big 40-SA200 hybrid
Miller Dynasty 280DX
Lincoln 210 MP
Miller 625 X-Treme
Hobart Handler 150
Victor Oxygen-acetylene torch
Miller/Lincoln Big 40-SA200 hybrid
- Otto Nobedder
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 06, 2011 11:40 pm
-
Location:Near New Orleans
Hey_allen,
That's brilliant!
We try to be a source of good ideas for each other, and you are in the running for a "Genie"
(That's a "genius of the year" award I JUST made up.)
That's a great example of thinking in unexpected ways!
Steve S
That's brilliant!
We try to be a source of good ideas for each other, and you are in the running for a "Genie"
(That's a "genius of the year" award I JUST made up.)
That's a great example of thinking in unexpected ways!
Steve S
Heh, it helps that I'd been scrounging around eBay recently trying to source a pressure switch to interlock the water cooler that I'm working on building for my CK20 torch.
(I don't want it to be easy to burn up the torch, so I'm putting in a pressure switch to keep the arc from lighting off when there isn't at least some pressure, how much yet to be decided, present on the water lines.)
That, and being a scrounge in the junk piles of salvaged and scrapped out equipment at work, including loads of pneumatic bits and pieces.
I'm just glad to at least share an idea, hopefully it works out!
(I don't want it to be easy to burn up the torch, so I'm putting in a pressure switch to keep the arc from lighting off when there isn't at least some pressure, how much yet to be decided, present on the water lines.)
That, and being a scrounge in the junk piles of salvaged and scrapped out equipment at work, including loads of pneumatic bits and pieces.
I'm just glad to at least share an idea, hopefully it works out!
-Josh
Greasy fingered tinkerer.
Greasy fingered tinkerer.
If you use a low voltage DC coil for the solenoid you could connect one side of power source to the frame. Attach the return side of solenoid to a wire attached to your glove. When you apply pressure to the sheet you close the circuit. You could use a thin switch as wrll that would trigger when pressed against the sheet.
Buy the best ear protection you can get and invite your neighbours to BBQ before you use it first time...
Allen, you should try and find a switch that trigger on flow. You'll have plenty pressure if the lines are clogged but zero flow.
Buy the best ear protection you can get and invite your neighbours to BBQ before you use it first time...
Allen, you should try and find a switch that trigger on flow. You'll have plenty pressure if the lines are clogged but zero flow.
Pictures from my scrap collection:
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
Bill Beauregard
- Bill Beauregard
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 9:32 pm
-
Location:Green Mountains of Vermont
Washing machines use a diaphragm switch to tell when the drum is full. Many can fill to more than one level. To test them I used to blow on the tube.
Anders: I looked at doing a flow switch, but the only one or two true flow switches that I found, I could find no information on their trigger range. The others were flow meters, either analog or digital pulse generator types, and I am trying to keep from having to do any programming on a micro-controller to manage a welder. I just don't want to have any sensitive electronics protecting it, due to the HF noise and interference.
Bill: Good idea on the washing machine barrel switches. I looked at them initially when I was shopping for a switch, but discarded them due to the very low trigger pressures, since I wanted mine to trigger around 50 psi, not 0.5 psi. They are cheap as well.
Bill: Good idea on the washing machine barrel switches. I looked at them initially when I was shopping for a switch, but discarded them due to the very low trigger pressures, since I wanted mine to trigger around 50 psi, not 0.5 psi. They are cheap as well.
-Josh
Greasy fingered tinkerer.
Greasy fingered tinkerer.
Return to “Welding Forum General Shop Talk”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities