Metal cutting - oxyfuel cutting, plasma cutting, machining, grinding, and other preparatory work.
Plasma cutting aluminum?
Post Reply
AKmud
  • Posts:
  • Joined:
    Fri Jan 25, 2013 1:47 am
  • Location:
    Wasilla, Alaska

Any tricks to get a clean cut? I've been cutting some 3/16" aluminum plate with my Miller 375 extreme. The machine cuts just fine but the edge is really grainy and rough. Suggestions?
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 06, 2011 11:40 pm
  • Location:
    Near New Orleans

Cutting with compressed N2 will help, but grinding disks are probably cheaper!

Every little bit helps, though. Do you have a good dryer in line to eliminate moisture/compresser oil? Also helps to use a new tip, and set the current low enough to drag the dip directly on the aluminum (say, 40-50A? slows the cut, but improves the edge).

Steve S
Top
delraydella
  • Posts:
  • Joined:
    Mon Apr 25, 2011 7:35 pm
  • Location:
    Detroit, MI

I've never had any luck plasma cutting aluminum. The edge always comes out very crappy.

I have used a Skil saw with a carbide tipped blade and a homemade saw guide to cut up to 1/2 thick aluminum plate. It works very well. If you have a table saw or access to one, a carbide tipped blade on that will cut plate, but be careful about kickback. There are saw blades specificly designed for cutting aluminum, they have a different rake angle on them than for wood, but any carbide tipped one will do, you just have to cut a little slower.

Other Steve
Welding☞Syncrowave 250,Millermatic 252,30a Spoolgun Cutting☞12" Hi-speed Cutoff Saw, 9x 12 Horizontal Bandsaw Milling☞Gorton 8d Vertical Mill Turning☞Monarch EE Precision Lathe Grinding ☞Brown & Sharpe #5 Surface Grinder
Top
AKmud
  • Posts:
  • Joined:
    Fri Jan 25, 2013 1:47 am
  • Location:
    Wasilla, Alaska

My problem is there aren't many straight lines on what I need to cut. The plasma cutter has good clean/dry air. I'm thinking about using my jigsaw...

This is what the cut looks like -

Image
Top
lazerbeam
  • Posts:
  • Joined:
    Tue Dec 20, 2011 7:50 am
  • Location:
    North Carolina

Otto Nobedder wrote:Cutting with compressed N2 will help, but grinding disks are probably cheaper!

Every little bit helps, though. Do you have a good dryer in line to eliminate moisture/compresser oil? Also helps to use a new tip, and set the current low enough to drag the dip directly on the aluminum (say, 40-50A? slows the cut, but improves the edge).

Steve S
Speaking of grinding discs, what have you found that works best on aluminum and aluminum dross?

Kevin
Top
User avatar
  • Posts:
  • Joined:
    Thu Jan 06, 2011 11:40 pm
  • Location:
    Near New Orleans

I'll have to look to be sure, but our disks are a German brand. "Schrupsheiben" or something like that. They make a grinding disk specifically for aluminum that works quite well, and doesn't load up. We get them from National Welding Supply.

That same aluminum disk is quite agressive on stainless, but goes away quickly with that use...

Steve S
Top
delraydella
  • Posts:
  • Joined:
    Mon Apr 25, 2011 7:35 pm
  • Location:
    Detroit, MI

That's pretty much how my plasma cuts on aluminum look. I just wind up sanding everything to a smooth surface.
Welding☞Syncrowave 250,Millermatic 252,30a Spoolgun Cutting☞12" Hi-speed Cutoff Saw, 9x 12 Horizontal Bandsaw Milling☞Gorton 8d Vertical Mill Turning☞Monarch EE Precision Lathe Grinding ☞Brown & Sharpe #5 Surface Grinder
Top
Post Reply

Return to “Metal Cutting”