[AKweldshop]

Ok guys had my buddy bring his 1991 dodge 3/4 ton plow truck my to replace a front u-joint.
While we were working on it, I noticed some of the crappiest welds on some of the plow mounts.

S000000.... Long story short, I ground all the welds out and welded them up again.

Enjoy.

BTW, the welds look like a cold 6011 on rusty O/A cut rotten steel.

IMG_1220.JPG (144.02 KiB) Viewed 960 times

IMG_1221.JPG (155.11 KiB) Viewed 960 times

IMG_1222.JPG (104.04 KiB) Viewed 960 times

[AKweldshop]

This piece I'm welding on is an extender to bring the plow out from under the truck farther.....
Nasty welds.
Amazing its held up this long.
Lots of cracks in these old plows, I just hit them with a grinder, a hot 8010 and done.

IMG_1223.JPG (64.37 KiB) Viewed 958 times

IMG_1224.JPG (56.05 KiB) Viewed 958 times

IMG_1225.JPG (55.71 KiB) Viewed 958 times

[AKweldshop]

This "attachment piece is mainly 1/4inch steel.
I'v ground out all the welds, and here are the pics.
I did some of the m uphill to.
Tons of fun.

IMG_1229.JPG (74.48 KiB) Viewed 956 times

IMG_1230.JPG (66.41 KiB) Viewed 956 times

IMG_1232.JPG (81.51 KiB) Viewed 956 times

[AKweldshop]

Welds coming soon....
As you know, welding is 90% prep, and 10% welding.
At least in my line of work.

IMG_1233.JPG (96.23 KiB) Viewed 956 times

Ok this weld is flat.
reverse lap joint.
5/32 7018 165amps.

IMG_1237.JPG (68.43 KiB) Viewed 956 times

This one here is flat and vertical.
1/8 7018 115amps.
Nasty steel, some slag in there and cut with a torch.

IMG_1241.JPG (108.18 KiB) Viewed 956 times

[AKweldshop]

Here's one of my vertical 7018 welds.
First pass was 5/32 8010 at 115amps.
Next I went uphill at 115amps with a 1/8 7018.

take it easy, I'm just a beginner.

IMG_1243.JPG (109.07 KiB) Viewed 956 times

IMG_1244.JPG (95.38 KiB) Viewed 956 times

IMG_1245.JPG (88.65 KiB) Viewed 956 times

[AKweldshop]

Replacing a U-joint on the ole dana 60.

IMG_1246.JPG (111.15 KiB) Viewed 954 times

Here's the ground clamp I use.

IMG_1238.JPG (114.74 KiB) Viewed 954 times

IMG_1239.JPG (135.77 KiB) Viewed 954 times

[AKweldshop]

Here's the other side.
I ground the old weld out.
5/32 8010 downihill.

I decided to do some stringers.
1/8 7018 at 115 amps.

IMG_1247.JPG (76.65 KiB) Viewed 953 times

IMG_1250.JPG (87.15 KiB) Viewed 953 times

IMG_1251.JPG (74.85 KiB) Viewed 953 times

[AKweldshop]

IMG_1252.JPG (66.9 KiB) Viewed 952 times

Than I uglied it up with a weave.

IMG_1254.JPG (83.71 KiB) Viewed 952 times

IMG_1255.JPG (87.34 KiB) Viewed 952 times

[AKweldshop]

IMG_1258.JPG (127.6 KiB) Viewed 952 times

Here's a shot of 3/32 7024 115amps.

All I've proven to myself is that I need practice....

[AKweldshop]

IMG_1240.JPG (109.84 KiB) Viewed 952 times

OH NOOOOO!!!!!!
I'm almost out of 1/8 7018!!!
This cant be happening to me!!!
I'll haft to close up, until I get more!!!!

Maybe I could greet people at WalMart until I can get some more....

~John

[AKweldshop]

Well,
She's done.

IMG_1283.JPG (63.13 KiB) Viewed 389 times

IMG_1284.JPG (79.55 KiB) Viewed 389 times