[Nomansland92]

I ordered 2lbs of .045 308l and 309l off Amazon and the seller put them in the same container without marketing either off them. I have both in 1/16 and tried welding all 4 side by side but I still couldn't quit tell the difference. I tried building up a blob to see if one was more magnetized but they all seemed pretty similar. Bottom one was 1/16 308l then goes 1/16 309l then the 2 unknowns in .045

Sent from my SM-G892A using Tapatalk

[LtBadd]

I would return them, promptly.

[Nomansland92]

I would return them, promptly.

I emailed the supplier, I'll see what they say

Sent from my SM-G892A using Tapatalk

[weldin mike 27]

An inspector told me during a course that a mass spectrometer is a way of determining material composition. Clearly his avalible tools vary somewhat from mine.

[Coldman]

Is the wire not stamped on the ends?


Sent using Tapatalk

[noddybrian]

If there is no flag / stamp assume it's Chinesium " shiny " metal - this is anything that fell in the melting pot - no need for numbers as it won't comply with any known spec ! even when they do stamp it it's a joke - I had a job come in where the customer supplied 316 tubing & elbows brand new mail order import stuff & it had surface rust on !

[cj737]

Is the wire not stamped on the ends?


Sent using Tapatalk

At 0.045, stamping is pretty hard to do

[Nomansland92]

Ya no stamping on it, probably because it's so small, But it sounds like there's no old timers trick to figuring it out. I appreciate the help though everyone!

Sent from my SM-G892A using Tapatalk

[LtBadd]

At 0.045, stamping is pretty hard to do

Real hard, I knew I had .045 stamped, not that its legible. The top of the 6 is missing...

Img_0886.jpg (69.91 KiB) Viewed 1220 times

[Nomansland92]

At 0.045, stamping is pretty hard to do

Real hard, I knew I had .045 stamped, not that its legible. The top of the 6 is missing... [emoji38]

Img_0886.jpg

Ya that would be at least something. This is all I got lol

Sent from my SM-G892A using Tapatalk

[LtBadd]

Mundaka Technologies
Business Description
Mundaka Technologies is located in Fort Lauderdale, Florida. This organization primarily operates in the Industrial Machinery and Equipment business / industry within the Wholesale Trade - Durable Goods sector. This organization has been operating for approximately 2 years. Mundaka Technologies is estimated to generate $592,754 in annual revenues, and employs approximately 3 people at this single location. This organization is engaged in importing activities at this facility.

Amazon is usually good about returns, you should be able to go to your account order history page and start the return process.

Do you have a LWS to buy from?

[Nomansland92]

Ya It shouldn't be a problem to return, more of just the hassle and the wait. I have a few lws shops but none that stock .045. This was actually the first time I had bought filler online haha, don't think I'll be doing again after this.

Sent from my SM-G892A using Tapatalk

[LtBadd]

Maybe the LWS can place the order, although if they don't want to stock it they probably want you to but 10lbs.

Ordering online shouldn't be an issue, I would recommend using either Arc-Zone, Cyberweld or IOC. There are others, but I would expect a good experience from these.

If you sign up to receive their email newsletter, you'll get $$ off your first order from Welding supplies from IOC

[Nomansland92]

Maybe the LWS can place the order, although if they don't want to stock it they probably want you to but 10lbs.

Ordering online shouldn't be an issue, I would recommend using either Arc-Zone, Cyberweld or IOC. There are others, but I would expect a good experience from these.

If you sign up to receive their email newsletter, you'll get $$ off your first order from Welding supplies from IOC

Ok I'll definitely check them out and order from one of them from now on. Thanks for the help!

Sent from my SM-G892A using Tapatalk