Is there really an issue leaving the gas up on the TIG unit? All the stuff I weld is really tiny - Seems like I waste more gas than I use purging out the gas. Nobody goes into my shop so there's no chance for somebody to fool with anything.
Z
Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
- Otto Nobedder
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 06, 2011 11:40 pm
-
Location:Near New Orleans
Z,
If I understand you correctly, you think leaving the gas on saves gas over what it takes to purge your lines?
That depends entirely on how tight your system is, but you don't have to purge lines just because the gas was off. If there's still pressure showing on the gauge, you're not "leaking air in" to your lines.
The safer bet is to close the argon when done. Even if you lose all line pressure, it takes less than a half-second to purge your lines unless you have some unusual setup.
Welcome to the group!
Steve S
If I understand you correctly, you think leaving the gas on saves gas over what it takes to purge your lines?
That depends entirely on how tight your system is, but you don't have to purge lines just because the gas was off. If there's still pressure showing on the gauge, you're not "leaking air in" to your lines.
The safer bet is to close the argon when done. Even if you lose all line pressure, it takes less than a half-second to purge your lines unless you have some unusual setup.
Welcome to the group!
Steve S
Steve, Thanks for getting back to me. I watch the gauge drop from 1500 and it seems like a lot of waste. System is killer tight.
Someplace I thought there was supposed to be some kind of potential for a problem if you left the Tank pressure against the System.
Good to have place to ask this kind of thing - the experience is a treasure trove!
Z
Someplace I thought there was supposed to be some kind of potential for a problem if you left the Tank pressure against the System.
Good to have place to ask this kind of thing - the experience is a treasure trove!
Z
I also always close the bottle and leave pressure in hoses. Next day I will check the pressure and if it have dropped I then know that system leaks.
Steve I have to disagree with purging time. Of course it depends that how long your gas hose is, but in orbital welding I have noticed that cleaning all the moisture can take one full weld before system is 100% clean. Even if lines are prepurged.
Little off topic, but it's also good to keep in mind that inpurities goes trough your hose. Gas atoms are relativily small and will penetrate hose. Even if gas hose inside pressure is greater than atmospheres.
Welcome to forum
Steve I have to disagree with purging time. Of course it depends that how long your gas hose is, but in orbital welding I have noticed that cleaning all the moisture can take one full weld before system is 100% clean. Even if lines are prepurged.
Little off topic, but it's also good to keep in mind that inpurities goes trough your hose. Gas atoms are relativily small and will penetrate hose. Even if gas hose inside pressure is greater than atmospheres.
Welcome to forum
-Markus-
- Otto Nobedder
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 06, 2011 11:40 pm
-
Location:Near New Orleans
Actually, the only thing that sees tank pressure is the regulator. All the hoses downstream see the regulated pressure, usually 50 or 75 psi on a "ball" type flowmeter, and quite a bit less on a two-stage regulator style.Zondfive wrote:Steve, Thanks for getting back to me. I watch the gauge drop from 1500 and it seems like a lot of waste. System is killer tight.
Someplace I thought there was supposed to be some kind of potential for a problem if you left the Tank pressure against the System.
Good to have place to ask this kind of thing - the experience is a treasure trove!
Z
Markus has a point about moisture and air infiltrataing unpressurized lines, and I'm used to having only 25' of 1/8" line on teh thorch side of the gas solenoid, so usually a second of pre-flow is plenty. However, when I get out my dry-rig, I have to assemble it and purge 125' of 1/4" hose, so I purge it a couple minutes, but this is at work and I'm not buying the gas.
There are also several ways to reduce "gas surge" at start-up, for further gas savings, and there's a topic somewhere in the TIG forum about it. I'll see if I can dig it up.
[EDIT] Topic on gas surge here: http://forum.weldingtipsandtricks.com/v ... f=5&t=4561
Steve S
Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities