Maybe that's been my problem all along. Why didn't I think of thatmotox wrote:maybe drinking two cans of soda instead of two beers
might be some of the answer ....
nice looking weld.
craig
Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
I don't know..., that "partially produced with genetic engineering" is a little creepy seeming as an ingredient.
I mean, I suppose it's no secret that most corn (and therefor the syrup) produced in N.A. is GMO.
But as a homebrewer, I know that barley is not a GMO crop. But I'm doing sparkling hard apple cider lately.
But, maybe I'll find some cans somewhere and try the challenge before too long.
I mean, I suppose it's no secret that most corn (and therefor the syrup) produced in N.A. is GMO.
But as a homebrewer, I know that barley is not a GMO crop. But I'm doing sparkling hard apple cider lately.
But, maybe I'll find some cans somewhere and try the challenge before too long.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
You are too hard on yourself...that is some good looking weld considering the material.dunkster wrote:ok, I'll play
....since my sh!t is starting to look somewhat presentable.
I had plenty of ferrous GTAW time when I first tried aluminum. Followed the Dynasty recommended settings and right out of the gate it was great.
Mind you, no welding school. I learned SMAW and GMAW in high school plus self taught oxyfuel and 2 weeks of GTAW in college.
One of these days I will get around to the beverage can challenge.
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
Go look on the side of the road. Cans everywhere. I seem to have noticed that a few regular contributers here have failed to show their entries into THE BEER CAN CHALLENGE. Being too busy isn't an excuse. Everyone finds time to come here and post...C. Livingstone wrote:I don't know..., that "partially produced with genetic engineering" is a little creepy seeming as an ingredient.
I mean, I suppose it's no secret that most corn (and therefor the syrup) produced in N.A. is GMO.
But as a homebrewer, I know that barley is not a GMO crop. But I'm doing sparkling hard apple cider lately.
But, maybe I'll find some cans somewhere and try the challenge before too long.
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
I'm not a regular yet but this looks interesting. I'll ask my teacher this week if I can give it a try. I'm not sure we have the right filler wire on hand.exnailpounder wrote: Go look on the side of the road. Cans everywhere. I seem to have noticed that a few regular contributers here have failed to show their entries into THE BEER CAN CHALLENGE. Being too busy isn't an excuse. Everyone finds time to come here and post...
Has anyone tried to just do a fusion weld?
:edit: Looks great dunkster!
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
No,
I'm not going to go looking along roadsides for beer cans to take this welding challenge with.
Besides, I'm still a new contributing forum member here.
You're going to have to wait till I get around to going and buying some pop or beer.
I'm not going to go looking along roadsides for beer cans to take this welding challenge with.
Besides, I'm still a new contributing forum member here.
You're going to have to wait till I get around to going and buying some pop or beer.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
I've not welded anything fit to post up yet.
But I've welded plenty that I can recycle! Here is Australia we are paid 10 cents per empty can at recycling depots. I suffered some interesting looks from the recycling guy over the weekend as he sorted through some badly welded cans, and finally the question "Do you think I should count this as one can or two?"
Kym
But I've welded plenty that I can recycle! Here is Australia we are paid 10 cents per empty can at recycling depots. I suffered some interesting looks from the recycling guy over the weekend as he sorted through some badly welded cans, and finally the question "Do you think I should count this as one can or two?"
Kym
- Otto Nobedder
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 06, 2011 11:40 pm
-
Location:Near New Orleans
One of the secrets to this, as I understand it, is to light up on the filler wire and wet it to the cans, otherwise most welders will just blow out the cans.Ryan_82 wrote: I'm not a regular yet but this looks interesting. I'll ask my teacher this week if I can give it a try. I'm not sure we have the right filler wire on hand.
Has anyone tried to just do a fusion weld?
:edit: Looks great dunkster!
I'm one of the "regulars" referred to above. I've not attempted this one.
Steve S
I plea guilty to that charge.exnailpounder wrote:I seem to have noticed that a few regular contributers here have failed to show their entries into THE BEER CAN CHALLENGE. Being too busy isn't an excuse.
To my defence I'm a good 30 hour flight away from my tools
Might give it a try, never did before.
Pictures from my scrap collection:
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
exnailpounder
- exnailpounder
-
Weldmonger
-
Posts:
-
Joined:Thu Dec 25, 2014 9:25 am
-
Location:near Chicago
I'm just joking with you guys. I am very slow with work right now and bored out of my mind so I thought I might take my frustration out on everyone I know we all have better things to do.....well maybe you guys do but not me...dammit.
Ifyoucantellmewhatthissaysiwillbuyyouabeer.
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
Yeah,
No sweat, exnailpounder.
Your fun prompting is motivational!
My retorts can be a little curt, but with some subtle sarcasm and dry humor mixed in, I think.
No sweat, exnailpounder.
Your fun prompting is motivational!
My retorts can be a little curt, but with some subtle sarcasm and dry humor mixed in, I think.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
Yeah,
It's funny, I used to refer to everything as "a Coke", coming from the West Coast of North America.
Later I used the term "soda" a lot.
Now it seems to be "pop".
It's funny, I used to refer to everything as "a Coke", coming from the West Coast of North America.
Later I used the term "soda" a lot.
Now it seems to be "pop".
LtBadd wrote:pop? are you from the north?C. Livingstone wrote: buying some pop or beer.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
- LtBadd
-
Weldmonger
-
Posts:
-
Joined:Sun Apr 12, 2015 4:00 pm
-
Location:Clearwater FL
-
Contact:
Well I'm a yankee and moved to Texas and got teased about that, and other things...C. Livingstone wrote:Yeah,
It's funny, I used to refer to everything as "a Coke", coming from the West Coast of North America.
Later I used the term "soda" a lot.
Now it seems to be "pop".
LtBadd wrote:pop? are you from the north?C. Livingstone wrote: buying some pop or beer.
Richard
Website
Website
Jeff
i'm going to use the same excuse i used for the razor blade weld.
i couldn't found 1/8" razor blades nor can i find beer cans made
out of .065 aluminum.
craig
i'm going to use the same excuse i used for the razor blade weld.
i couldn't found 1/8" razor blades nor can i find beer cans made
out of .065 aluminum.
craig
htp invertig 221
syncrowave 250
miller 140 mig
hypertherm plasma
morse 14 metal devil
syncrowave 250
miller 140 mig
hypertherm plasma
morse 14 metal devil
GreinTime
- GreinTime
-
Weldmonger
-
Posts:
-
Joined:Fri Nov 01, 2013 11:20 am
-
Location:Pittsburgh, PA
It's pop. Get over it, like meow! It's also said creek (with a long E sound), and it's correctly spelled washed (and pronounced like that) while we're on the subject of colloquial misnomers and bad pronunciation!LtBadd wrote:pop? are you from the north?C. Livingstone wrote: buying some pop or beer.
Sent from my VS995 using Tapatalk
#oneleggedproblems
-=Sam=-
-=Sam=-
sedanman
- sedanman
-
Ace
-
Posts:
-
Joined:Sun Jan 03, 2016 2:54 pm
-
Location:Beacon and Pawling, New York
Just undertook this endeavor today. Quite fun and frustrating at the same time. I am out of coupons but l am certain my neighbors will be able to supply all l could need. This looks better in person than it does on camera. This is one of the better results. Warts and all, right?
- Attachments
-
- 20170110_095438.jpg (29.52 KiB) Viewed 2118 times
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
Hey,
Not bad, Sedanman.
Yeah, I found a few beer cans last night and started dabbling with them, and it certainly was tricky, at least for me.
I'll probably go to the store today for some nice new cans and get back to this.
Not bad, Sedanman.
Yeah, I found a few beer cans last night and started dabbling with them, and it certainly was tricky, at least for me.
I'll probably go to the store today for some nice new cans and get back to this.
Last edited by C. Livingstone on Tue Jan 10, 2017 12:04 pm, edited 1 time in total.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
I too, am a yankee and when I moved to Texas I called it soda and got teased because they called it pop.LtBadd wrote:
Well I'm a yankee and moved to Texas and got teased about that, and other things...
Edit: My wife corrected me and she is the one from Texas. They called it "soda water".
Last edited by electrode on Tue Jan 10, 2017 7:43 pm, edited 1 time in total.
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
Well,
What the heck do most Texans like to call it?
Soda-pop? Carbonated beverage? Ha, ha, ha...
What the heck do most Texans like to call it?
Soda-pop? Carbonated beverage? Ha, ha, ha...
electrode wrote:I too, am a yankee and when I moved to Texas I called it soda and got teased because they called it pop.LtBadd wrote:
Well I'm a yankee and moved to Texas and got teased about that, and other things...
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Steve, Craig, Keith and Ryan, thank you gents.
Thankfully this did not require pics from both sides of the can . I am thoroughly convinced that the thickness varies in this area of the bottom as you go around it. Some places it just up and vaporizes away. Anyone else notice that?
Think this will be my new go to exercise for shaking the cobb webs off, being as I go so long without lighting up.
Thankfully this did not require pics from both sides of the can . I am thoroughly convinced that the thickness varies in this area of the bottom as you go around it. Some places it just up and vaporizes away. Anyone else notice that?
Think this will be my new go to exercise for shaking the cobb webs off, being as I go so long without lighting up.
I was experimenting with lighting up on flat bar and moving it over to the edge of 2 pieces of strip I had cut from a can, just stacked on one another.
I had a play with it. I could keep a low amp arc going provided I bumped the frequency way up and kept the arc gap around 1mm, once the arc got too wide the hf kicked in took a big bite out of the edge. Could just about get a fusion weld on the edge of the two strips though.
I had a play with it. I could keep a low amp arc going provided I bumped the frequency way up and kept the arc gap around 1mm, once the arc got too wide the hf kicked in took a big bite out of the edge. Could just about get a fusion weld on the edge of the two strips though.
Nowadays people know the price of everything and the value of nothing... Oscar Wilde
Ok... Excuse time ....
Lets see, well I only had 2 cans, and there is only so much ginger beer I can drink. All my real bear comes in bottles
Seriously though, what a pain in the arse this is. I did a root pass (looked shite), several fill passes for practice and to clean up the root pass (they looked shite too), then tried to clean it up again and ended up with this big dodgy cap which I did at about 100 amps and weaving side to side to cover the width of the beads below.
Really need to light up on the filler and get it to melt itself in. I ground the electrode to a point and put a flat on the end. Bumped the frequency way up hoping to tighten up the arc somewhat. I only have 2.4mm rod on hand, probably would have been better with 1.6mm as the 2.4mm takes a bit too much heat to wet in. Or simply practice a lot more.
Lets see, well I only had 2 cans, and there is only so much ginger beer I can drink. All my real bear comes in bottles
Seriously though, what a pain in the arse this is. I did a root pass (looked shite), several fill passes for practice and to clean up the root pass (they looked shite too), then tried to clean it up again and ended up with this big dodgy cap which I did at about 100 amps and weaving side to side to cover the width of the beads below.
Really need to light up on the filler and get it to melt itself in. I ground the electrode to a point and put a flat on the end. Bumped the frequency way up hoping to tighten up the arc somewhat. I only have 2.4mm rod on hand, probably would have been better with 1.6mm as the 2.4mm takes a bit too much heat to wet in. Or simply practice a lot more.
Nowadays people know the price of everything and the value of nothing... Oscar Wilde
- C. Livingstone
-
Guide
-
Posts:
-
Joined:Sat Dec 03, 2016 9:22 am
Yeah,
I bought an 8-pack of small, 7.5oz Coke cans, since I envisioned myself having to drink the soda faster than I thought I might master the task.
But those little cans had a short lip where the red color was real close to the joint, which may have added to a contamination of the puddle problem. So I drank the first two, but then dumped the rest as I quickly burned through them and about 20 CF of Argon. Ha, ha, ha... But I did start to have a little luck with an "Advanced Pulse" or Mix/TIG feature on my machine, which I've otherwise never used for anything.
I might get back to this before too long, as a neighbor consumes a lot of soda and has plenty of normal, already empty cans.
Wheeeeeee, this welding stuff is fun!!!!!!!!!!
I bought an 8-pack of small, 7.5oz Coke cans, since I envisioned myself having to drink the soda faster than I thought I might master the task.
But those little cans had a short lip where the red color was real close to the joint, which may have added to a contamination of the puddle problem. So I drank the first two, but then dumped the rest as I quickly burned through them and about 20 CF of Argon. Ha, ha, ha... But I did start to have a little luck with an "Advanced Pulse" or Mix/TIG feature on my machine, which I've otherwise never used for anything.
I might get back to this before too long, as a neighbor consumes a lot of soda and has plenty of normal, already empty cans.
Wheeeeeee, this welding stuff is fun!!!!!!!!!!
Rupes wrote:Ok... Excuse time ....
Lets see, well I only had 2 cans, and there is only so much ginger beer I can drink. All my real bear comes in bottles
Last edited by C. Livingstone on Thu Jan 12, 2017 5:37 pm, edited 1 time in total.
Peace be with you all,
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Christian Livingstone
www.youtube.com/newjerusalemtimes
Everlast AC/DC 210EXT (2015)
CAT250D DC-TIG/Plasma Combo
Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities