Page 1 of 1

TIG welding: Adding filler metal; need tips and tricks :)

Posted: Wed Jun 12, 2013 12:24 am
by wolverine_arc
Hi mates;

i'm in welding school right now. it's my day 5 on the training program.

need tips and tricks on adding filler metal continuously for a better weld beads.

any video links and advice from you guys will be highly appreciated :)

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Wed Jun 12, 2013 1:32 am
by JKR
Take a piece of filler rod home and practice the first way he shows you (or some variation of it) and STOP listening. The rest of his input is bad. There's alot of self taught welders out there. Most of them have gotten along just fine because they'll never do work that needs to meet a code.

http://www.youtube.com/watch?v=MOSopEgTh0A

Also, at the back end of the filler rod make a 90 degree bend (1-2 inches). It will keep the rod from bounce around alot.

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Wed Jun 12, 2013 8:36 am
by zank
There are some nice shots of Rick working the filler in this video.
http://youtu.be/DVZAEdJ89ug

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Wed Jun 12, 2013 5:56 pm
by Otto Nobedder
JKR wrote:...Also, at the back end of the filler rod make a 90 degree bend (1-2 inches). It will keep the rod from bounce around alot.

This also makes the rod much easier to retrieve from a table or floor with your gloves on! ;)

Steve S

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Wed Jun 12, 2013 6:13 pm
by Otto Nobedder
I typically get my most consistent beads using the "lay-wire" technique. The trick is choosing the wire diameter that will deposit just the amount of metal you want. I've done a cap with two 3/32" rods together, just to get the finished height I wanted. (Doesn't work well with aluminum, though, at least for me.)

There's a topic here with a pic of that. I'll see if I can find it.

Actually, I'll just repost it. This pic is all free-hand work, but works just as well for walk-the-cup.
GEDC0797.JPG
GEDC0797.JPG (197.21 KiB) Viewed 1162 times
Steve S

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Fri Jun 14, 2013 9:23 am
by wolverine_arc
Otto Nobedder wrote:I typically get my most consistent beads using the "lay-wire" technique. The trick is choosing the wire diameter that will deposit just the amount of metal you want. I've done a cap with two 3/32" rods together, just to get the finished height I wanted. (Doesn't work well with aluminum, though, at least for me.)

There's a topic here with a pic of that. I'll see if I can find it.

Actually, I'll just repost it. This pic is all free-hand work, but works just as well for walk-the-cup.
GEDC0797.JPG
Steve S
i'll take your advice :)

try to watch Jody's video on lay-wire technique, too.

Re: TIG welding: Adding filler metal; need tips and tricks :

Posted: Fri Jun 14, 2013 9:25 am
by wolverine_arc
JKR wrote:Take a piece of filler rod home and practice the first way he shows you (or some variation of it) and STOP listening. The rest of his input is bad. There's alot of self taught welders out there. Most of them have gotten along just fine because they'll never do work that needs to meet a code.

http://www.youtube.com/watch?v=MOSopEgTh0A

Also, at the back end of the filler rod make a 90 degree bend (1-2 inches). It will keep the rod from bounce around alot.
@red:

thanks mate. :)