Hey all.
I've been welding some thin wall mild steel tube. 1.5mm wall thickness, 45-50 amps, 1.6mm zirconiated electrode.
Weld behaves itself, making neat little coins. Good control of arc length and puddle, arc is white/blue through my shield, everything normal, when suddenly there's a bright green flash - so bright it wipes out my eyesight. Stop welding. Re-start, all normal until another bright green flash stops play. This then keeps happening, sometimes just now and then, sometimes more often.
Only thing I can think of is that while I had angle-ground and acetone wiped the face of the tube, the inside checks out a little dirty because I just can't get in there.
Is it, as I suspect, contamination that is causing these bright green flashes?
Kym
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
- Braehill
-
Weldmonger
-
Posts:
-
Joined:Sat Jul 06, 2013 11:16 am
-
Location:Near Pittsburgh,Pennsylvania. Steel Buckle of the Rust Belt
Kym,
Zirconiated tungsten is not usually used while welding DCEN and might be splintering off and causing problems. It will spit pieces into the arc.
Another thing to check is if your welding at low amperage with an auto darkening helmet it might be going light on you. Check the sensitivity setting and move it higher in a bright area until it darkens and then back it off just a little. I might have that ass backwards, you might have to lower it, it's 03:30 in the morning here so forgive me if I have it wrong.
Len
Zirconiated tungsten is not usually used while welding DCEN and might be splintering off and causing problems. It will spit pieces into the arc.
Another thing to check is if your welding at low amperage with an auto darkening helmet it might be going light on you. Check the sensitivity setting and move it higher in a bright area until it darkens and then back it off just a little. I might have that ass backwards, you might have to lower it, it's 03:30 in the morning here so forgive me if I have it wrong.
Len
Now go melt something.
Instagram @lenny_gforce
Len
Instagram @lenny_gforce
Len
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
Thanks guys.
Oh, and my apologies, the electrode I was using was actually 2% Lanthanated.
Had my white tips and blue tips mixed up.
Will check the helmet adjustment though - good tip.
Kym
Oh, and my apologies, the electrode I was using was actually 2% Lanthanated.
Had my white tips and blue tips mixed up.
Will check the helmet adjustment though - good tip.
Kym
As the others said. Increase sensitivity but you might also gain some by increasing delay time. That will keep lens dark longer so it might not flash.
I get this often on low amp stainless welding and above have helped.
I get this often on low amp stainless welding and above have helped.
Pictures from my scrap collection:
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
http://forum.weldingtipsandtricks.com/v ... f=9&t=5677
+1 increase delay(I sort of match delay to= post flow-sort of-)AndersK wrote:As the others said. Increase sensitivity but you might also gain some by increasing delay time. That will keep lens dark longer so it might not flash.
I get this often on low amp stainless welding and above have helped.
Everlast 250EX
Miller 250 syncrowave
Sharp LMV Vertical Mill
Takisawa TSL-800-D Lathe
Coupla Bandsaws,Grinders,surface grinder,tool/cutter grinder
and more stuff than I deserve(Thanks Significant Other)
Miller 250 syncrowave
Sharp LMV Vertical Mill
Takisawa TSL-800-D Lathe
Coupla Bandsaws,Grinders,surface grinder,tool/cutter grinder
and more stuff than I deserve(Thanks Significant Other)
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
Just took a look at my helmet.
Oops...it doesn't even have those adjustments! It has 'on' and 'darkness".
Time for a new helmet!
Kym
Oops...it doesn't even have those adjustments! It has 'on' and 'darkness".
Time for a new helmet!
Kym
ex framie
- ex framie
-
Ace
-
Posts:
-
Joined:Sun Aug 09, 2015 1:09 am
-
Location:Brisbane QLD Land of oz
Kym,
I had a similar issue with my now replaced 4 year old WIA auto helmet.
I replaced it with one of these.
http://www.totaltools.com.au/cigweld-st ... dpCLmVuvxA
The 4 sensors make a difference when working around stuff, very nice head band, good viewing area and I think 1/20,000 sec reaction time.
Now there are better, faster reacting and more expensive helmets out there, but it seems pretty good for the pricepoint and I havent been flashed with it as yet.
Cheers
I had a similar issue with my now replaced 4 year old WIA auto helmet.
I replaced it with one of these.
http://www.totaltools.com.au/cigweld-st ... dpCLmVuvxA
The 4 sensors make a difference when working around stuff, very nice head band, good viewing area and I think 1/20,000 sec reaction time.
Now there are better, faster reacting and more expensive helmets out there, but it seems pretty good for the pricepoint and I havent been flashed with it as yet.
Cheers
Pete
God gave man 2 heads and only enough blood to run 1 at a time. Who said God didn't have a sense of humour.....
God gave man 2 heads and only enough blood to run 1 at a time. Who said God didn't have a sense of humour.....
- MosquitoMoto
-
Weldmonger
-
Posts:
-
Joined:Sat Aug 01, 2015 8:38 am
-
Location:The Land Down Under
Great tip, thanks Pete.ex framie wrote:Kym,
I had a similar issue with my now replaced 4 year old WIA auto helmet.
I replaced it with one of these.
http://www.totaltools.com.au/cigweld-st ... dpCLmVuvxA
The 4 sensors make a difference when working around stuff, very nice head band, good viewing area and I think 1/20,000 sec reaction time.
Now there are better, faster reacting and more expensive helmets out there, but it seems pretty good for the pricepoint and I havent been flashed with it as yet.
Cheers
I have a Total Tools store nearby...and Fathers Day coming up...
Kym