Well ,when ya got a new welder you just gotta have a new cart and old idea just don't work. Here's what !
Working on a cooler for the bottom next.
Doug
What welding projects are you working on? Are you proud of something you built?
How about posting some pics so other welders can get some ideas?
How about posting some pics so other welders can get some ideas?
I just hooked up a WeldCraft wp20 to my cooler and here's how I did it. Any comments? I looked at some other peoples ideas and went the same route.
- Attachments
-
- photo (9).JPG (89.2 KiB) Viewed 5710 times
-
- photo (8).JPG (91.99 KiB) Viewed 5710 times
Sweet Ive been looking ito getting a wp20 too But dodnt know if I want to go the route you went with that adapter block.DWRIGHT wrote:I just hooked up a WeldCraft wp20 to my cooler and here's how I did it. Any comments? I looked at some other peoples ideas and went the same route.
I still need a cooler but Your giving me ideas.
Good work on the set up.
jameswswanson
- jameswswanson
-
New Member
-
Posts:
-
Joined:Fri Jan 21, 2011 5:55 pm
Nice cart!... and solution to the after market water cooled torch, but is it easy to switch the setup around?
Decision time.... First off I'm either getting a 250EX (then save my pennies forever for a plasma cutter) or a PP256, but before I put in my order I want to figure a few things out. I already have a water cooler, so I'm looking for a solution for hooking up an aftermarket Water cooled (ck 200) torch to a PP256, however the adapter block would make switching between Welding and Cutting a chore. Am I wrong? Also switching between Argon and Air... Has anyone come up with a clever solution, or will this drive me as nuts as I think it will.
Decision time.... First off I'm either getting a 250EX (then save my pennies forever for a plasma cutter) or a PP256, but before I put in my order I want to figure a few things out. I already have a water cooler, so I'm looking for a solution for hooking up an aftermarket Water cooled (ck 200) torch to a PP256, however the adapter block would make switching between Welding and Cutting a chore. Am I wrong? Also switching between Argon and Air... Has anyone come up with a clever solution, or will this drive me as nuts as I think it will.
Using a CK200 setup is simple. Here is how I did mine on my 250ex.jameswswanson wrote:Nice cart!... and solution to the after market water cooled torch, but is it easy to switch the setup around?
Decision time.... First off I'm either getting a 250EX (then save my pennies forever for a plasma cutter) or a PP256, but before I put in my order I want to figure a few things out. I already have a water cooler, so I'm looking for a solution for hooking up an aftermarket Water cooled (ck 200) torch to a PP256, however the adapter block would make switching between Welding and Cutting a chore. Am I wrong? Also switching between Argon and Air... Has anyone come up with a clever solution, or will this drive me as nuts as I think it will.
http://www.everlastgenerators.com/forum ... art-s.html
You will just need whatever fittings it takes to adapt to your cooler.
I have seen a post where someone used a three way fitting to switch between Argon to Air quickly on their 256, but don't remember off hand on what board it was posted on.
Millermatic 251
Spectrum 300 Plasma
Everlast PowerTig 250EX
Everlast PowerCool W300
Harris/Victor OA
Craftsman 13 Speed Drill Press
ProTools Air/Hydraulic Bender
48" Brake
Compressor, Notchers, Grinders, etc.
Spectrum 300 Plasma
Everlast PowerTig 250EX
Everlast PowerCool W300
Harris/Victor OA
Craftsman 13 Speed Drill Press
ProTools Air/Hydraulic Bender
48" Brake
Compressor, Notchers, Grinders, etc.
jameswswanson
- jameswswanson
-
New Member
-
Posts:
-
Joined:Fri Jan 21, 2011 5:55 pm
Thank you very much! This was exactly what I was looking for, the red adapter plug. Switching between Tig And Plasma will be a cinch with this setup.
Return to “Welding Projects - Welding project Ideas - Welding project plans”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities