[AKweldshop]

IMG_5814.JPG (77.72 KiB) Viewed 18204 times

IMG_5815.JPG (71.36 KiB) Viewed 18204 times

IMG_5816.JPG (71.95 KiB) Viewed 18204 times

[AKweldshop]

IMG_5817.JPG (83.79 KiB) Viewed 18203 times

IMG_5818.JPG (90.8 KiB) Viewed 18203 times

IMG_5819.JPG (57.91 KiB) Viewed 18203 times

[AKweldshop]

IMG_5820.JPG (75.9 KiB) Viewed 18203 times

IMG_5821.JPG (68.24 KiB) Viewed 18203 times

IMG_5822.JPG (83.77 KiB) Viewed 18203 times

[AKweldshop]

IMG_5823.JPG (87.56 KiB) Viewed 18203 times

To be continued!!!!

~John

[AKweldshop]

IMG_5830.JPG (63.13 KiB) Viewed 18195 times

IMG_5831.JPG (96.4 KiB) Viewed 18195 times

IMG_5832.JPG (90.33 KiB) Viewed 18195 times

[AKweldshop]

IMG_5833.JPG (58.19 KiB) Viewed 18519 times

IMG_5834.JPG (50.38 KiB) Viewed 18519 times

IMG_5835.JPG (102.44 KiB) Viewed 18519 times

[AKweldshop]

First passes.
1/8 7018 at 140 amps.
knife edge, and 1/8" to 1/4" root opening.

IMG_5836.JPG (94.6 KiB) Viewed 18520 times

IMG_5837.JPG (101.05 KiB) Viewed 18520 times

IMG_5838.JPG (84.59 KiB) Viewed 18520 times

[AKweldshop]

IMG_5839.JPG (75.27 KiB) Viewed 18519 times

IMG_5841.JPG (85.91 KiB) Viewed 18519 times

IMG_5842.JPG (109.12 KiB) Viewed 18519 times

[AKweldshop]

First pass is burned in, and read for the fill/cap.
Using 5/32" Esab 8018.

Invertec 250 set at about this range.

IMG_5843.JPG (93.56 KiB) Viewed 18518 times

IMG_5844.JPG (49.83 KiB) Viewed 18518 times

IMG_5845.JPG (90.46 KiB) Viewed 18518 times

[AKweldshop]

Decided to run a 3g on the bottom.

Need practice for sure.

IMG_5846.JPG (67.36 KiB) Viewed 18506 times

IMG_5847.JPG (84.6 KiB) Viewed 18506 times

IMG_5849.JPG (63.32 KiB) Viewed 18506 times

[AKweldshop]

IMG_5850.JPG (93.14 KiB) Viewed 18478 times

IMG_5851.JPG (85.91 KiB) Viewed 18478 times

IMG_5852.JPG (104.59 KiB) Viewed 18478 times

[AKweldshop]

IMG_5853.JPG (102.18 KiB) Viewed 18477 times

IMG_5854.JPG (85.33 KiB) Viewed 18477 times

IMG_5855.JPG (111.01 KiB) Viewed 18477 times

[AKweldshop]

IMG_5857.JPG (104.24 KiB) Viewed 18477 times

IMG_5858.JPG (43.31 KiB) Viewed 18477 times

IMG_5859.JPG (47.57 KiB) Viewed 18477 times

[AKweldshop]

IMG_5863.JPG (93.31 KiB) Viewed 18479 times

IMG_5864.JPG (87.55 KiB) Viewed 18479 times

IMG_5865.JPG (55.49 KiB) Viewed 18479 times

[AKweldshop]

IMG_5867.JPG (78.67 KiB) Viewed 18473 times

IMG_5868.JPG (83.17 KiB) Viewed 18473 times

IMG_5869.JPG (60.63 KiB) Viewed 18473 times

[AKweldshop]

IMG_5870.JPG (75.62 KiB) Viewed 18595 times

IMG_5871.JPG (69.92 KiB) Viewed 18595 times

IMG_5872.JPG (70.88 KiB) Viewed 18595 times

[AKweldshop]

I reaaly should have used 5/32 7024 for capping....
Oh well,
Next one I guess.

IMG_5873.JPG (92 KiB) Viewed 18593 times

IMG_5874.JPG (69.96 KiB) Viewed 18593 times

IMG_5875.JPG (79.45 KiB) Viewed 18593 times

[Superiorwelding]

John,
Thanks for the pictures. That looks like a lot of hard work there. I will say good job. The only thing is the backer plate is not necessarily needed but it won't hurt anything. Keep us posted in your projects, I for one look forward to the pics.
-Jonathan

[AKweldshop]

IMG_5876.JPG (64.5 KiB) Viewed 18583 times

IMG_5877.JPG (69.82 KiB) Viewed 18583 times

IMG_5878.JPG (46.04 KiB) Viewed 18583 times

[AKweldshop]

A recap of all 8 sides.

IMG_5882.JPG (91.97 KiB) Viewed 18583 times

IMG_5883.JPG (95.46 KiB) Viewed 18583 times

IMG_5884.JPG (130.76 KiB) Viewed 18583 times

[AKweldshop]

IMG_5885.JPG (108.78 KiB) Viewed 18553 times

IMG_5886.JPG (98.06 KiB) Viewed 18553 times

IMG_5887.JPG (112.17 KiB) Viewed 18553 times

[AKweldshop]

IMG_5888.JPG (100.55 KiB) Viewed 18553 times

IMG_5889.JPG (104.32 KiB) Viewed 18553 times

[AKweldshop]

Need to wire wheel it down, and paint it....

Welds always look better with paint...

IMG_5891.JPG (83.58 KiB) Viewed 18553 times

[AKweldshop]

Need some feedback guys......

[79jasper]

Looking good so far.
But it's hard to say, without knowing what the final product needs to look like. [WINKING FACE]

Sent from my SM-G900R4 using Tapatalk