Small portable welding table

AndersK · Mon Nov 07, 2016 5:51 pm

Been fabricating a small fixture table lately.
Plate is 600x500x8 mm.
Have wanted a decent table for long but dont have the space for it so I made this to be somewhat portable.
The rollers will not engage until its folded and tilted a bit.
Made some stronghand type clamps to use with it.
Just the handle to weld on and its completed.

: IMG_20161107_2723.jpg (48.35 KiB) Viewed 4933 times

: IMG_20161107_44334.jpg (49.86 KiB) Viewed 4933 times

: IMG_20161107_56980.jpg (44.34 KiB) Viewed 4933 times

exnailpounder · Mon Nov 07, 2016 6:50 pm

Nice job Anders. That looks like 1/2" plate on the top...how many drill bits did you wear out drilling those holes

Ooops just read that the top is 8mm..pays to read the wholepost sometimes

Mon Nov 07, 2016 7:58 pm

8mm is 5/16, give or take a few thousandths....

Okay, 8mm is .3149" versus .3125" for 5/16... After I said it, I had to do the math.

Steve S

AndersK · Tue Nov 08, 2016 2:01 am

Thanks Jeff
Actually the bit is still like new after 50 holes. Used an Alfra Rotabest core bit with plenty cutting fluid.

rednation12 · Tue Nov 08, 2016 10:02 pm

what patterned did you do for the wholes or space in between thanks

AndersK · Wed Nov 09, 2016 3:56 am

Roughly 2" between rows and 4" between holes. First hole is offset 2" from previous row

AndersK · Wed Nov 09, 2016 4:07 pm

Made a torch holder to fit both a 9- and 26-torch.

: IMG_20161109_51230.jpg (30.56 KiB) Viewed 4813 times

: IMG_20161109_48396.jpg (31.9 KiB) Viewed 4813 times

: IMG_20161109_36897.jpg (30.29 KiB) Viewed 4813 times

jroark · Thu Nov 10, 2016 3:25 pm

My uncle just gave me a smaller roll around metal table with no top on it so I bet you know what I'm thinking now. Man that's a good idea! I really like the table and clamps. Been wanting a fixture table myself so I might give that a try too. Nice work.

AndersK · Thu Nov 10, 2016 4:57 pm

Thx.
As a friend of mine use to say, good ideas are meant for stealing

exnailpounder · Thu Nov 10, 2016 6:23 pm

I really like the torch cradle! Was that your design? Very talented!

AndersK · Fri Nov 11, 2016 4:02 am

Thx Jeff, yes my design. Some "engineering-on-the-fly" and hand bending the wire.
I really hate the ones one can by where you need to tilt and twist to release it. Almost like one of those metal puzzles

AndersK · Wed Nov 23, 2016 4:59 pm

Ready to use now

: IMG_20161119_234634.jpg (73.67 KiB) Viewed 3472 times

exnailpounder · Wed Nov 23, 2016 5:26 pm

Nice job Anders! Is that a morse taper I see on the table? You have a lathe too? I like looking around other guys shops

motox · Thu Nov 24, 2016 7:23 am

jeff
you can't beat a drill bit in the tail stock to bore
holes in anything you can chuck up!
craig

exnailpounder · Thu Nov 24, 2016 8:37 am

motox wrote:jeff
you can't beat a drill bit in the tail stock to bore
holes in anything you can chuck up!
craig

I am taking my time and looking for a small lathe to play with. I don't know alot about them and haven't used one since Highschool but more and more I am finding the need to make small parts.

AndersK · Thu Nov 24, 2016 5:24 pm

Thx Jeff. Yes its a mt2, good eyes

Sadly just for the pillar drill.
Havent got the space for a lathe nor mill, otherwise there would be no end of the madness

MosquitoMoto · Thu Nov 24, 2016 5:29 pm

AndersK wrote:Thx Jeff. Yes its a mt2, good eyes
Sadly just for the pillar drill.
Havent got the space for a lathe nor mill, otherwise there would be no end of the madness

The ideal workshop is a place where the madness never ends...lathe...mill...forge...3D printer...vapour blaster...etc...

Kym

exnailpounder · Fri Nov 25, 2016 12:02 am

:

MosquitoMoto wrote:
AndersK wrote:Thx Jeff. Yes its a mt2, good eyes
Sadly just for the pillar drill.
Havent got the space for a lathe nor mill, otherwise there would be no end of the madness

The ideal workshop is a place where the madness never ends...lathe...mill...forge...3D printer...vapour blaster...etc...

Kym

What I lack in ability, I make up for in tools. I need a lathe like I need a hole in the head but I will still get one and then sit and look at it 6 months later and wonder why I bought it...Can welding fumes cause that?

MosquitoMoto · Fri Nov 25, 2016 1:44 am

I need a lathe for dozens of reasons.

* Spare knurled footpegs for rearsets

* Spare connecting rods (shift, brake) for rearsets

* Wheel spacers

* Swingarm spacers

* Disc spacers

* Frame bungs...I could go on.

...I could go on. The fact is, virtually nothing I need to make on a lathe would be very technically challenging or complex, yet all are items which, if I had to approach a local machine shop to create then, would cost me proper money.

Time to get a cheapie Siegl or similar.

Kym

AndersK · Sun Nov 27, 2016 5:19 pm

Made a handrest tonight. Long enough to reach diagonally if needed.

: IMG_20161127_44336.jpg (52.1 KiB) Viewed 3403 times

: IMG_20161127_33468.jpg (37.26 KiB) Viewed 3403 times

exnailpounder · Sun Nov 27, 2016 7:37 pm

Nice Anders! You're WAY more creative than I am...I usually steal my ideas and then take credit for it

rahtreelimbs · Sun Nov 27, 2016 7:45 pm

Andersk......where did you get the legs?

AndersK · Mon Nov 28, 2016 1:39 am

Well I probably shouldnt take credit for the arm rest. Seen a coupple before, Jonathan made one I remember from a while ago. Think Jody has one in a video too.
Thx anyway.

The legs? I made them from 22 mm aluminium tubes.

motox · Mon Nov 28, 2016 9:24 am

if you look at some of Andersk metal projects you will
recognize hie abilities at shaping metal.
craig

AndersK · Mon Nov 28, 2016 4:46 pm

Well, thank you Craig that was very kind said