Page 1 of 1
My 3x7 welding table build.
Posted: Wed May 07, 2014 1:07 pm
by AKweldshop
I'll have less than $20 in it when I'm done.
Pics later.
~John
Re: My 3x7 welding table build.
Posted: Wed May 07, 2014 2:19 pm
by Superiorwelding
John,
What's up with that? I got all excited to look at your table and there was no pitures.
-Jonathan
Re: My 3x7 welding table build.
Posted: Wed May 07, 2014 3:09 pm
by AKweldshop
I'm blocked from pics for a little while.
Let me sort it out.
~John
Re: My 3x7 welding table build.
Posted: Wed May 07, 2014 5:21 pm
by Antorcha
Is it a conversion from a bench at Glacier NP ?
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 12:14 am
by AKweldshop
This table started out as the fabbed together bunch of channel.
And this 5'x10' sheet of 3/8 steel.
- IMG_1937.JPG (118.99 KiB) Viewed 14038 times
- IMG_1938.JPG (93.44 KiB) Viewed 14038 times
- IMG_1946.JPG (77.56 KiB) Viewed 14038 times
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 12:18 am
by AKweldshop
- IMG_1942.JPG (58.2 KiB) Viewed 14036 times
- IMG_2018.JPG (78.39 KiB) Viewed 14036 times
- IMG_2020.JPG (86.42 KiB) Viewed 14036 times
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 12:24 am
by AKweldshop
- IMG_2021.JPG (82.21 KiB) Viewed 14033 times
- IMG_2022.JPG (82.62 KiB) Viewed 14033 times
- IMG_2024.JPG (97.08 KiB) Viewed 14033 times
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 12:33 am
by AKweldshop
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 12:40 am
by AKweldshop
- IMG_2056.JPG (70.74 KiB) Viewed 14026 times
- IMG_2057.JPG (81.13 KiB) Viewed 14026 times
- IMG_2085.JPG (74.56 KiB) Viewed 14026 times
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 4:20 am
by noddybrian
Nice bit of re-cycling - it must be nice living where you are - seems like there's plenty of old steel & bits laying around for cheap if you have the ability to use them - no such luck here - last decent scrapyard got shut down a few years back - nothing around now - if I need metal it all has to be bought new which can make side projects real expensive - not sure I'd like how long your winters are though.
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 11:15 am
by AKweldshop
For some reason I like it up here.
Been here almost 15yrs.
Lots of auctions, tool loaded yard sales, and deals.
Winters are easily overcome, get a large warm shop.
John
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 2:43 pm
by noddybrian
The bits visible in your photos looks like a nice place to be - in my ignorance the only things I know about your state are from watching Ice Road Truckers / Bering sea gold / Ax Men / Deadliest Catch - these are some of my favorite TV programs - naturally we don't get them here - but that's what piracy is for right ? !!
Re: My 3x7 welding table build.
Posted: Sat May 10, 2014 9:01 pm
by mcoe
I am going to have to build me a good table. The only tables I have are a cheap 3' x 2' table from northern tool, very cheap piece of junk now, and a piece of scrap that is about 14"x 4'. I need to start one of these projects. Very nice table.
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:08 pm
by AKweldshop
Gentleman....
Finally got to putting a bottom shelf in.
Got some 17" wide sheets of 3/4' plywood at the dump.
Enjoy the pics, and yes, I'm loving this table!!!!
- IMG_5626.JPG (48.03 KiB) Viewed 11861 times
- IMG_5627.JPG (56.29 KiB) Viewed 11861 times
- IMG_5628.JPG (51.22 KiB) Viewed 11861 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:15 pm
by AKweldshop
- IMG_5629.JPG (56.36 KiB) Viewed 11861 times
- IMG_5630.JPG (51.3 KiB) Viewed 11861 times
- IMG_5633.JPG (79.27 KiB) Viewed 11861 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:18 pm
by AKweldshop
- IMG_5634.JPG (79.32 KiB) Viewed 11861 times
- IMG_5636.JPG (63.29 KiB) Viewed 11861 times
- 2 pieces on 1 1/2" angle iron.
- IMG_5637.JPG (60.4 KiB) Viewed 11861 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:23 pm
by AKweldshop
- IMG_5638.JPG (122.27 KiB) Viewed 11860 times
- IMG_5639.JPG (62.79 KiB) Viewed 11860 times
- IMG_5640.JPG (63.24 KiB) Viewed 11860 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:27 pm
by AKweldshop
- IMG_5641.JPG (45.79 KiB) Viewed 11859 times
- IMG_5642.JPG (33.09 KiB) Viewed 11859 times
- IMG_5643.JPG (79.25 KiB) Viewed 11859 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:38 pm
by AKweldshop
- IMG_5644.JPG (56.46 KiB) Viewed 11859 times
- IMG_5649.JPG (94.22 KiB) Viewed 11859 times
- IMG_5650.JPG (92.53 KiB) Viewed 11859 times
Re: My 3x7 welding table build.
Posted: Wed Jul 30, 2014 11:46 pm
by AKweldshop
- IMG_5651.JPG (63.31 KiB) Viewed 11858 times
- IMG_5652.JPG (94.8 KiB) Viewed 11858 times
Gotta get my shop all organized, been a mess for a while....
I'm thinking of stacking all my 50lb boxes on this shelf, and free up my other table.
- IMG_3871.JPG (51.28 KiB) Viewed 11858 times
Re: My 3x7 welding table build.
Posted: Thu Jul 31, 2014 10:18 am
by mcoe
Re: My 3x7 welding table build.
Posted: Thu Jul 31, 2014 5:28 pm
by AKweldshop
Bahahaha!!!!!
Not a lick of them in my shop...