Stick Welding Tips, Certification tests, machines, projects
If some one have a good trick....
I think of using a thin piano wire as a remote control (attached at my wrist for instance)
But if I learn how to hold steadily the rod without touching and with one hand ....
They talk of a "peep" position https://weldingengineers.co.nz/safety-e ... /kem-p1700 possible the one with the mask just a little open (?)
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Nah, no peeking.
A trick I learned for fixed shade helmets is to find your mark and set the rod a little to its side so that it sits on the flux and doesn't strike, then put the hood down, pivot the rod up and strike.
A trick I learned for fixed shade helmets is to find your mark and set the rod a little to its side so that it sits on the flux and doesn't strike, then put the hood down, pivot the rod up and strike.
Thank you Pete, that is exactly what I was after , simple but efficient. So for instance you put the rod at 45 degres on its side at the level of the beginning of the "smoke trail" (the 1" used to light the rod before reverting direction)PeteM wrote:Nah, no peeking.
A trick I learned for fixed shade helmets is to find your mark and set the rod a little to its side so that it sits on the flux and doesn't strike, then put the hood down, pivot the rod up and strike.
Then a wrist motion put the rod where it must be , to strike. I imagine the motion fairly well I will try that soon.
Regards
Pianos , restorer and tuner
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Dedicated to learn welding since april
slowly learning not complaining of doing beads and beads
pro inverter PROGYS 200 FV PFC CEL+tig lift
OA Oxyflam 1000 cutting and welding gas torch
Return to “Stick Welding/Arc Welding - Shielded Metal Arc Welding”
Jump to
- Introductions & How to Use the Forum
- ↳ Welcome!
- ↳ Member Introductions
- ↳ How to Use the Forum
- ↳ Moderator Applications
- Welding Discussion
- ↳ Metal Cutting
- ↳ Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding
- ↳ Mig and Flux Core - gas metal arc welding & flux cored arc welding
- ↳ Stick Welding/Arc Welding - Shielded Metal Arc Welding
- ↳ Welding Forum General Shop Talk
- ↳ Welding Certification - Stick/Arc Welding, Tig Welding, Mig Welding Certification tests - Welding Tests of all kinds
- ↳ Welding Projects - Welding project Ideas - Welding project plans
- ↳ Product Reviews
- ↳ Fuel Gas Heating
- Welding Tips & Tricks
- ↳ Video Discussion
- ↳ Wish List
- Announcements & Feedback
- ↳ Forum News
- ↳ Suggestions, Feedback and Support
- Welding Marketplace
- ↳ Welding Jobs - Industrial Welding Jobs - Pipe Welding Jobs - Tig Welding Jobs
- ↳ Classifieds - Buy, Sell, Trade Used Welding Equipment
- Welding Resources
- ↳ Tradeshows, Seminars and Events
- ↳ The Welding Library
- ↳ Education Opportunities