General welding questions that dont fit in TIG, MIG, Stick, or Certification etc.
Post Reply
NYWELDERJim
  • Posts:
  • Joined:
    Sun Feb 24, 2013 1:09 am
  • Location:
    Poughkeepsie, NY

Can anyone tell me the brand of welding table used in many of Jody's videos? My machine shop operation has an ancient welding table which offers NO versatility and takes a long time to setup for anything even slightly complex. I have seen how fast and easy it is to fixture parts on the table Jody uses.

Does anyone have suggestions on other brands of welding tables?

Thanks!

Jim
KP161
  • Posts:
  • Joined:
    Wed Feb 20, 2013 3:47 am
  • Location:
    Niagara Region, Ontario Canada

User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Hey,

Go to the above link, it is called the Build pro table. There are a few different sizes.

As for other brands, Google Fabrication Tables and see what pops up.

Mick
NYWELDERJim
  • Posts:
  • Joined:
    Sun Feb 24, 2013 1:09 am
  • Location:
    Poughkeepsie, NY

Thank you very much! I visited the Build Pro website, it shows some awesome products! Lot's of fixturing, clamps, guides. I am going to get in contact with a dealer in my area and see what the prices are for the various options.

Best regards,

Jim
User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Hey,

Pleasure, while you are talking to them, my address is..... :D

mick
Mike
  • Posts:
  • Joined:
    Mon Dec 06, 2010 1:09 pm
  • Location:
    Andover, Ohio

nice stuff but not cheep.
M J Mauer Andover, Ohio

Linoln A/C 225
Everlast PA 200
NYWELDERJim
  • Posts:
  • Joined:
    Sun Feb 24, 2013 1:09 am
  • Location:
    Poughkeepsie, NY

Their system looks to be available in sections or modules. I am looking at getting a basic table and some fixturing then adding to it as I can afford it. A little at a time.

Jim
User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Hey,

I was looking through the WT& T page and found some strong hand vids,

http://www.weldingtipsandtricks.com/wel ... video.html

http://www.weldingtipsandtricks.com/str ... lding.html

Mick
watermelon
  • Posts:
  • Joined:
    Tue Feb 19, 2013 10:37 am

summitracing.com sells these tables and fixtures too
User avatar
  • Posts:
  • Joined:
    Thu Jan 06, 2011 11:40 pm
  • Location:
    Near New Orleans

There was a topic here, under "projects", I think, where a fellow build his own, and did an incredible job on the cheap!

Any of the regulars (Mick?) remember where that was? I'll have a hunt, or maybe the OP will read this thread?

Steve S
User avatar
  • Posts:
  • Joined:
    Fri Apr 01, 2011 10:59 pm
  • Location:
    Australia; Victoria

Hey,

Here it is. Man i love this site( translate to ......i spend too much time here.)

http://forum.weldingtipsandtricks.com/v ... 2252#p9579

Mick
Post Reply