Whatcing that Jody welding different type rods. I became curious what kind of bead i could lay down. And this was ESAB rods it was 63.?? but anyway 3,2 mm 125Amps makes nice looking weld.
- Attachments
-
- 20141226_171247.jpg (24.76 KiB) Viewed 4426 times
-
- 20141226_171321.jpg (31.51 KiB) Viewed 4426 times
-
- 20141226_171537.jpg (43.11 KiB) Viewed 4426 times
- weldin mike 27
-
Weldmonger
-
Posts:
-
Joined:Fri Apr 01, 2011 10:59 pm
-
Location:Australia; Victoria
A few pic of 6013/6012 jobs. 3.25mm for joints, and 2.5 for the welded writing. About 90-130amps.
- Attachments
-
- uploadfromtaptalk1420107932969.jpg (49.15 KiB) Viewed 4424 times
-
- uploadfromtaptalk1420107848725.jpg (61.56 KiB) Viewed 4424 times
-
- uploadfromtaptalk1420107813699.jpg (52.75 KiB) Viewed 4424 times
-
- uploadfromtaptalk1420107711530.jpg (45.83 KiB) Viewed 4424 times
- AKweldshop
-
Weldmonger
-
Posts:
-
Joined:Wed Oct 23, 2013 3:30 pm
-
Location:Palmer AK
You guy's evidently have some nice 6013.... 
Just a couple welders and a couple of big hammers and torches.
Men in dirty jeans built this country, while men in clean suits have destroyed it.
Trump/Carson 2016-2024
Men in dirty jeans built this country, while men in clean suits have destroyed it.
Trump/Carson 2016-2024
- MinnesotaDave
-
Weldmonger
-
Posts:
-
Joined:Sun Oct 27, 2013 10:57 pm
-
Location:Big Lake/Monticello MN, U.S.A.
Washington Alloy is good 6013 and only $2 per pound around hereAKweldshop wrote:You guy's evidently have some nice 6013....
Dave J.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~
Syncro 350
Invertec v250-s
Thermal Arc 161 and 300
MM210
Dialarc
Tried being normal once, didn't take....I think it was a Tuesday.
- Superiorwelding
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 10:13 pm
-
Location:Eddy, TX
Great looking welds guys. Like Jody said in his last video, I admire those who use 6013 welding pipe. I need to try is some time.
-Jonathan
-Jonathan
Instagram- @superiorwelding/@learntotig
Twitter- @_JonathanLewis
https://www.learntotig.com
https://www.superiorweldandfab.com
https://www.youtube.com/+SuperiorWeldin ... ATHANLEWIS
Twitter- @_JonathanLewis
https://www.learntotig.com
https://www.superiorweldandfab.com
https://www.youtube.com/+SuperiorWeldin ... ATHANLEWIS
noddybrian
- noddybrian
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 12:13 pm
Unless Esab markets using different number systems around the world if it were 6013 the number would be 46.00 - rods starting 63.XX are in the austenitic stainless range & under the generic term " Almat " - maybe the numbers are different in the UK ?
- weldin mike 27
-
Weldmonger
-
Posts:
-
Joined:Fri Apr 01, 2011 10:59 pm
-
Location:Australia; Victoria
Here's a bad one. I worked on an unrelated job on this trailer but could not let this go.
- Attachments
-
- uploadfromtaptalk1420190858577.jpg (49.93 KiB) Viewed 4349 times
YEAP My mistake it was 43.32noddybrian wrote:Unless Esab markets using different number systems around the world if it were 6013 the number would be 46.00 - rods starting 63.XX are in the austenitic stainless range & under the generic term " Almat " - maybe the numbers are different in the UK ?
When you get that rod at right angel runs nice beads, but that slag is easily in front of the budle if the rod Angel is too litle. That "worm hole effect comes bretty easily whit thees Esab 6013rods"
noddybrian
- noddybrian
-
Weldmonger
-
Posts:
-
Joined:Thu Jan 24, 2013 12:13 pm
Easy to mistake - either they print those numbers smaller or my eyes are getting worse ! - never used the 43.32 - most suppliers here tend to stock the 46.00 ( Miltrode ) not sure what the difference is in use - does'nt look much difference on the Esab website - whatever the rod it's a very good looking weld - just don't start AK off about 6013 !
Esab also do a 6013 numbered OK 43.32 , cant say i have ever used them as i always turn to Murex Vodex or Vortec Marine when i want a good 6013noddybrian wrote:Unless Esab markets using different number systems around the world if it were 6013 the number would be 46.00 - rods starting 63.XX are in the austenitic stainless range & under the generic term " Almat " - maybe the numbers are different in the UK ?
Murex 353is TransTig
Esab Aristo Mig 4001i Pulse
Murex 406s Transmig
Esab Aristo Mig 4001i Pulse
Murex 406s Transmig