Tig welding tips, questions, equipment, applications, instructions, techniques, tig welding machines, troubleshooting tig welding process
Difficult Tig Brazing - Steel Wire to 1/4" square bar
Post Reply
Icepick
  • Posts:
  • Joined:
    Wed Sep 18, 2013 5:37 pm

Hi Guys and Gals, I'm having some trouble on this one. I'm building some placard stands out of 1/4" square bar and I need to braze or weld 1/16 wire to it as tabs to hold the placard in. I've been trying to tig braze some stainless or mild steel welding rod, but both seem to have about the same melting point as the braze. I can't puddle the brazing rod without melting the steel rod. Also, the heat's not enough to puddle the bar. I'm running 25-40 amps DC, straight Argon. Any ideas or better methods? Thanks.
Top
Rick_H
  • Posts:
  • Joined:
    Sat Feb 08, 2014 1:50 pm
  • Location:
    PA/MD

Maybe preheat the square bar, then speed tack it (no filler), hit it with high amps quick.
I weld stainless, stainless and more stainless...Food Industry, sanitary process piping, vessels, whatever is needed, I like to make stuff.
ASME IX, AWS 17.1, D1.1
Instagram #RNHFAB
Top
dirtmidget33
  • Posts:
  • Joined:
    Tue May 13, 2014 5:22 pm

No need to braze it in or use filler. Just use the rod itself like filler. puddle the base metal shove your 1/16 rod in puddle like using it as filler. Leave rod in puddle as you taper out. Then trim rod to desired length.
why use standard nozzles after gas lens where invented. Kinda of like starting fires by rubbing sticks together.
Top
User avatar
  • Posts:
  • Joined:
    Sat Mar 08, 2014 10:39 pm
  • Location:
    Holley, FL

dirtmidget33 wrote:No need to braze it in or use filler. Just use the rod itself like filler. puddle the base metal shove your 1/16 rod in puddle like using it as filler. Leave rod in puddle as you taper out. Then trim rod to desired length.
Like playing with a hot glue gun is what I envisioned as I was reading this.
Top
dirtmidget33
  • Posts:
  • Joined:
    Tue May 13, 2014 5:22 pm

0308160853-1.jpg
0308160853-1.jpg (44.69 KiB) Viewed 743 times
Here is an example of what I'm talking about this is 3/32 to 3/8. Used as rain deer tails on Xmas thing. You can pick up the whole display holding on to this tail and it weighs 35pounds. Your bead can be smaller than this, I pushed rod into puddle a little to much on this one. For this application it was fine and is a lot smaller then it looks in the blown up close up too. Remember that's only a 3/32 rod
Last edited by dirtmidget33 on Tue Mar 08, 2016 2:04 pm, edited 5 times in total.
why use standard nozzles after gas lens where invented. Kinda of like starting fires by rubbing sticks together.
Top
User avatar
  • Posts:
  • Joined:
    Thu May 07, 2015 11:46 am
  • Location:
    KY.

dirtmidget33 wrote:No need to braze it in or use filler. Just use the rod itself like filler. puddle the base metal shove your 1/16 rod in puddle like using it as filler. Leave rod in puddle as you taper out. Then trim rod to desired length.
I've done this many times. It works well.
Freddie
Top
Icepick
  • Posts:
  • Joined:
    Wed Sep 18, 2013 5:37 pm

Thanks for your help guys. I tried each of your methods with mixed results. I am still learning. I got them to stick with the speed tacks, but gave when I tested adjustability. The placards are going in later by someone else. The pool and dip method worked for the first end, but I had to bend it around and do the same to the other end. That proved very tedious and I had many failures. I ended up giving up on wire and cut some 16 ga strips and rosette welding to a pre-placed tack on the square bar. Again, thanks so much for the ideas. I'll keep those in my toolbox for when I get better with the small stuff.
Top
Post Reply

Return to “Tig Welding - Tig Welding Aluminum - Tig Welding Techniques - Aluminum Tig Welding”